Mounting A Tub

Website

Listed here down the page you can locate a good deal of wonderful insights around A Step-by-Step Guide to Installing a Bathtub.


How to Install a Bathtub
Mounting a tub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also often, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard job. If the old bathtub is readily obtainable, the project can relocate quickly; if you have to open a wall surface to remove the old bathtub and place the brand-new bathtub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable trying it. As opposed to hiring a professional to take control of a halfway-completed project, it is much better to take into consideration employing one before you start. Chances are you may require a specialist plumber to make tube links.
This article will aid you install a brand-new bath tub in your restroom if you have actually currently purchased a brand-new bathtub and don't require to change the plan of your previous water system pipes.
Your tools and also material checklist must comprise the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Preparing for the Installation


    First of all, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets unit to prevent stress on the bath tub.
    Fit the versatile tap ports to the bottom of both faucets using 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use all of the supplied washers.
    Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its last setting.

    Removing Old Taps


    If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the water system. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the restricted access that is usually the situation.
    Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
    Prior to carrying on to fit the new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

    Setting up the Bathtub


    Making use of the two wooden boards under its feet, put the bathtub in the called for position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
    The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub till the spirit level reviews level.
    To mount taps, fit all-time low of the furthest adaptable tap adapter to the appropriate supply pipeline by making a compression join; after that do the same for the various other faucet.
    Turn on the water as well as examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and additionally inspect the overflow outlet as well as the regular outlet for leakages.
    Lastly, deal with the bath paneling as defined in the maker's instruction manual. Tiling as well as sealing around the tub should wait up until the bathtub has been made use of a minimum of when as this will resolve it right into its final position.

    Suitable New Taps


    If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a link to the existent supply pipes.
    If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
    Next, place the tap in the placing hole in the bath/basin making sure that the washing machines remain in place between the faucet and also the sink. Secure the faucet in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former kind should be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Tiling Around the Bath tub


    In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split an inflexible seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, causing issues with wetness and also feasible leakages to the ceiling below.
    You can select from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of soaked paper or soft rope. Remember to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not think about this motion prior to sealing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily readily available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof adhesive and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    As a fervent person who reads about A Step-by-Step Guide to Installing a Bathtub, I think sharing that excerpt was appropriate. Enjoyed reading our blog posting? Please share it. Help someone else locate it. We recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.




    Schedule Your Job Now


    Leave a Reply

    Your email address will not be published. Required fields are marked *